Direct View on the Origin of High Li+ Transfer Impedance in All-Solid-State Battery

Large interfacial resistance plays a dominant role in the performance of all-solid-state lithium-ion batteries. However, the mechanism of interfacial resistance has been under debate. Here, the Li⁺ transport at the interfacial region is investigated to reveal the origin of the high Li⁺ transfer impedance in a LiCoO₂(LCO)/LiPON/Pt all-solid-state battery. Both an unexpected nanocrystalline layer and a structurally disordered transition layer are discovered to be inherent to the LCO/LiPON interface. Under electrochemical conditions, the nanocrystalline layer with insufficient electrochemical stability leads to the introduction of voids during electrochemical cycles, which is the origin of the high Li⁺ transfer impedance at solid electrolyte-electrode interfaces. In addition, at relatively low temperatures, the oxygen vacancies migration in the transition layer results in the formation of Co₃O₄ nanocrystalline layer with nanovoids, which contributes to the high Li⁺ transfer impedance. This work sheds light on the mechanism for the high interfacial resistance and promotes overcoming the interfacial issues in all-solid-state batteries.     

Influence of Se and Te substitutions at Tl-site of Tl(Ba,Sr)CaCu2O7 superconductor on the AC susceptibility and electrical properties

The Sr and Ba bearing Tl-1212 phase, Tl(Ba,Sr)CaCu₂O₇ is an interesting superconductor. The Sr only bearing TlSr₂CaCu₂O₇ is not easily prepared in the superconducting form. The Ba only bearing TlBa₂CaCu₂O₇ on the other hand does not show improvement in the transition temperature with elemental substitution. In this work the influence of multivalent Se (non-metal) and Te (metalloid) substitutions at the Tl-site of Tl_1-xM_x(Ba,Sr)CaCu₂O₇ (M = Se or Te) superconductors for x = 0–0.6 was studied. The samples were prepared via the conventional solid-state reaction method. XRD patterns showed a single Tl-1212 phase for x = 0 and 0.1 Se substituted samples. The critical current density at the peak temperature, T_p of the imaginary (χ”) part of the AC susceptibility (χ = χ’ +χ”), J_c-inter(T_p) for all samples was between 15 and 21 A cm⁻². The highest superconducting transition temperature was shown by the x = 0.3 Se-substituted sample (T_c-onset = 104 K, T_c-zero = 89 K, T_cχ’ = 104 K and T_p = 80 K). Te suppressed the superconductivity of Tl-1212 phase. The order of highest transition temperatures are as follows: Tl_1-xTe_x(Ba,Sr)CaCu₂O₇<Tl(Ba,Sr)CaCu₂O₇<Tl_1-xSe_x(Ba,Sr)CaCu₂O₇. This work showed that Se was better than Te in improving the transition temperature and flux pinning of the Tl-1212 phase. The roles of ionic radius of Se and Te on the superconductivity of Tl(Ba,Sr)CaCu₂O₇ are discussed in this paper.     

Preparation and electrochemical characterization of Ti-based amorphous metallic glass with high strength

Ti-based amorphous metallic glasses have excellent mechanical, physical, and chemical properties, which is an important development direction and research hotspot of metal composite reinforcement. As a stable, simple, efficient, and large-scale preparation technology of metallic powders, the gas atomization process provides an effective way of preparing amorphous metallic glasses. In this study, the controllable fabrication of a Ti-based amorphous powder, with high efficiency, has been realized by using gas atomization. The scanning electron microscope, energy-dispersive spectrometer, and X-ray diffraction are used to analyze surface morphology, element distribution, and phase structure, respectively. A microhardness tester is used to measure the mechanical property. An electrochemical workstation is used to characterize corrosion behavior. The results show that as-prepared microparticles are more uniform and exhibit good amorphous characteristics. The mechanical test shows that the hardness of amorphous powder is significantly increased as compared with that before preparation, which has the prospect of being an important part of engineering reinforced materials. Further electrochemical measurement shows that the corrosion resistance of the as-prepared sample is also significantly improved. This study has laid a solid foundation for expanding applications of Ti-based metallic glasses, especially in heavy-duty and corrosive domains.     

Psoriasis and Gut Microbiome—Current State of Art

Psoriasis is a chronic, immune-mediated inflammatory disease that affects around 125 million people worldwide. Several studies concerning the gut microbiota composition and its role in disease pathogenesis recently demonstrated significant alterations among psoriatic patients. Certain parameters such as Firmicutes/Bacteroidetes ratio or Psoriasis Microbiome Index were developed in order to distinguish between psoriatic and healthy individuals. The “leaky gut syndrome” and bacterial translocation is considered by some authors as a triggering factor for the onset of the disease, as it promotes chronic systemic inflammation. The alterations were also found to resemble those in inflammatory bowel diseases, obesity and certain cardiovascular diseases. Microbiota dysbiosis, depletion in SCFAs production, increased amount of produced TMAO, dysregulation of the pathways affecting the balance between lymphocytes populations seem to be the most significant findings concerning gut physiology in psoriatic patients. The gut microbiota may serve as a potential response-to-treatment biomarker in certain cases of biological treatment. Oral probiotics administration as well as fecal microbial transplantation were most reported in bringing health benefits to psoriatic patients. However, the issue of psoriatic bacterial gut composition, its role and healing potential needs further investigation. Here we reviewed the literature on the current state of the relationship between psoriasis and gut microbiome.     

Fabrication and properties of the superhydrophobic ceria-based composite coating on magnesium alloy

A superhydrophobic ceria-based composite coating is developed to improve anticorrosion properties of AZ61 magnesium alloy, fabricating via chemical conversion method followed by hydrothermal treatment. The cerium conversion coating has a block structure with microcracks. After the hydrothermal treatment, a dense CeO₂ layer, porous CeO₂ nanorods, and stearic absorbing layers are grown stepwise on the conversion coating. And the composite coating is hydrophobic or even superhydrophobic and has almost no microcracks. As the hydrothermal reaction time increases, the water contact angle of the composite coating first increases and then decreases, and it reaches the maximum value of 152° after hydrothermal treatment for 4 h. Both the dense CeO₂ layer and the superhydrophobic stearic absorbing layer can effectively prevent the electrolyte from contacting the substrate; the corrosion current density of the superhydrophobic composite coating is lower than that of the hydrophilic composite coating and the cerium conversion coating, and has the best corrosion resistance.     

Potential influence of microorganisms on the corrosion of carbon steel in the French high- and intermediate-level long-lived radioactive waste disposal context

In the context of the high-level radioactive waste disposal CIGEO, the corrosion rate due to microbially influenced corrosion (MIC) has to be evaluated. In France, it is envisaged to dispose of high- and intermediate-level long-lived radioactive waste at a depth of 500 m in a deep geological disposal, drilled in the Callovo-Oxfordian claystone (Cox) formation. To do so, a carbon steel casing will be inserted inside disposal cells, which are horizontal tunnels drilled in the Cox. A specific cement grout will be injected between the carbon steel casing and the claystone. A study was conducted to evaluate the possibility of MIC on carbon steel in the foreseeable high radioactive waste disposal. The corrosiveness of various environments was investigated at 50°C and 80°C with or without microorganisms enriched from samples of Andra's underground research laboratory. The monitoring of corrosion during the experiments was ensured using gravimetric method and real-time corrosion monitoring using sensors based on the measurements of the electrical resistance. The corrosion data were completed with microbiological analyses including cultural and molecular characterizations.     

Scaling analysis of hydrogen flow with carbon dioxide cushion gas in subsurface heterogeneous porous media

Subsurface hydrogen (H₂) storage in geological formations is of growing interest for decarbonization. However, there is a knowledge gap in understanding the multiphase flow involved in this process, which can have a significant impact on the recovery performance of H₂. Therefore, a full-compositional modeling study was conducted to analyze potential issues and to understand the fundamental hydrodynamic mechanisms of H₂ storage. We performed a range of 2D vertical simulations at the decametre scale with a very fine cell size (0.1 m) to observe the detailed flow behaviour of H₂ with carbon dioxide (CO₂) as cushion gas in various flow regimes. Issues such as viscous instability, capillary bypassing, gas trapping and gravity segregation are analysed here. To generalize our calculations, we have validated and applied the scaling theory in the context of subsurface H₂ storage. Since this study is focused on the hydrodynamic behaviour, three dimensionless groups, including aspect factor, capillary/viscous ratio and gravity/viscous ratio were identified to correlate recovery performance between various scales in a fixed heterogeneous system. It was found that H₂ could infiltrate the cushion gas in the proximity of the injectors, meaning that CO₂ is not displaced away from the injectors in a piston-like fashion. As a result, the purity of the back produced H₂ is much degraded, particularly in a viscous-dominated scenario. On the other hand, the injected H₂ mostly accumulates at the top forming a highly restricted mixing zone with CO₂ in the gravity-dominated case. The recovery performance is therefore much improved in this case. Although the gas distribution can be significantly altered by capillary forces leading to bypassed zones, the recovery performance of H₂ is hardly influenced. This is because the back-produced H₂ recovery is not dependent on the sweep efficiency of the gas. H₂ can be back produced following the same paths which were formed during injection.     

Responses to comments on the paper “two-dimensional Sc2C: A reversible and high capacity hydrogen storage material predicted by first-principles calculations”

A recent commentary by Santhosh and Ravindran on our paper (Int. J. Hydrogen Energy 2014, 39:10,606) demonstrated that the interaction between H₂ and MXene (Sc₂C and Ti₂C) phases are not Kubas-type and should be of weak physisorption, and thus made a conclusion that 2D Sc₂C and Ti₂C are not suitable for practical hydrogen storage applications. In this responses, we recalculated hydrogen adsorption on 2D Sc₂C and Ti₂C by using different exchange-correlation functionals. And based on the calculated results, bare MXenes (especially the Ti₂C) are suitable as hydrogen storage materials at temperatures of several tens degrees lower than room temperature. And the hydrogen adsorptions on the MXenes terminated with oxygen group were also investigated. Among the Ti₂C, Sc₂C and their oxygen-functional counterparts, the binding energy of H₂ on Sc₂CO₂ surface is the closest to the ideal range of 0.16–0.42 eV/H₂ at ambient conditions, and thus the Sc₂C with oxygen group is expected to be more suitable as hydrogen storage materials.